Mellowing out Air Norton neck in Charvel So-Cal?

  • 3 Replies
  • 214 Views

0 Members and 1 Guest are viewing this topic.

*

Offline Speeddemon

  • Full Member
  • ***
  • 221
  • 10
    • View Profile
    • TRIBUTÖR - HIGH VOLTAGE 80's HEAY ROCK
Mellowing out Air Norton neck in Charvel So-Cal?
« on: October 31, 2022, 01:08:08 PM »
So the Air Norton is one of my favourite neck pickups; it's in an Ibanez S540FM, in a Burny Les Paul Standard and in a 2010 MIJ Charvel So-Cal Pro Mod.

And while I love its split-tones, in the Charvel I've come to find it too 'plingy' and bright in the top end when playing distorted leads (in a Maiden tribute, where it's my "Adrian Smith" guitar).
The guitar has an alder body, maple neck, maple fretboard, Floyd Rose with an FU big brass block and a DiMarzio Norton in the bridge. 1x 500k push/pull volume, no tone pot.
Originally it came with an Evo neck and ToneZone bridge, but I went through numerous pickup changes to come to the Air Norton/Norton combo.

Is there a way to mellow out/thicken the Air Norton (even if it means slightly mellowing/thickening) without lowering the output? So I'm not looking to lower the pickup height.

Would a 300k pot help here?
In use: 13x DiMarzio (7 gtrs), 7x Duncan (3 gtrs).
Got preference? ;)

*

Offline darkbluemurder

  • Global Moderator
  • Hero Member
  • *****
  • 1507
  • 48
    • View Profile
Re: Mellowing out Air Norton neck in Charvel So-Cal?
« Reply #1 on: November 01, 2022, 05:14:47 AM »
The Air Norton is already very smooth in the neck. If it is not smooth enough, there are the following options:

- use a cap and resistor in series to simulate the non-existing tone pot. The downside is that this will affect the bridge pickup as well.
- put a 1 meg resistor from the switch terminal where the neck pickup is connected to ground. This will let the neck pickup and the both pickup selections "see" a 330k load but leave the bridge pickup at 500k.

Both easy to try and easy to reverse if you don't like it.

Good luck,
Stephan

Area 67, Area 58, Area 61, VV Pro 54, Injectors, VV HB2, Virtual Solo, SDS-1, Area T, Area Hot T, Area T 615, Virtual Hot T, Chopper T, Bluesbucker, Breed set, Air Norton, Super Distortion, DLX+, DLX-90, DP240, DP198, DP168, VPAF b, AT-1, Mo' Joe, FRED, Humbucker from Hell, Super 2

*

Offline Speeddemon

  • Full Member
  • ***
  • 221
  • 10
    • View Profile
    • TRIBUTÖR - HIGH VOLTAGE 80's HEAY ROCK
Re: Mellowing out Air Norton neck in Charvel So-Cal?
« Reply #2 on: November 01, 2022, 08:58:14 AM »
Thanks man, I'll try the 1 MOhm resistor, see how that flies.  :D
In use: 13x DiMarzio (7 gtrs), 7x Duncan (3 gtrs).
Got preference? ;)

*

Offline darkbluemurder

  • Global Moderator
  • Hero Member
  • *****
  • 1507
  • 48
    • View Profile
Re: Mellowing out Air Norton neck in Charvel So-Cal?
« Reply #3 on: November 08, 2022, 05:11:51 AM »
The standard resistor values would give the following loads (approx) with a 500k pot:

470k - 235k
1meg - 330k
1.5meg - 365k
1.65meg (i.e. 2 x 3.3meg in parallel) - 385k
2.2meg - 410k

Good luck,
Stephan
Area 67, Area 58, Area 61, VV Pro 54, Injectors, VV HB2, Virtual Solo, SDS-1, Area T, Area Hot T, Area T 615, Virtual Hot T, Chopper T, Bluesbucker, Breed set, Air Norton, Super Distortion, DLX+, DLX-90, DP240, DP198, DP168, VPAF b, AT-1, Mo' Joe, FRED, Humbucker from Hell, Super 2