Help with Washburn N24 wiring

  • 5 Replies
  • 6437 Views

0 Members and 2 Guests are viewing this topic.

*

Offline ledvedder

  • Full Member
  • ***
  • 168
  • 3
    • View Profile
Help with Washburn N24 wiring
« on: November 24, 2018, 09:59:10 PM »
I'm trying to replace the dull Washburn neck pickup in my N24 with a Duncan Jazz. But, I want to be sure what I have before I start disconnecting things. What I'm seeing doesn't match any of the wiring diagrams that I'm finding online. It's 2 Humbucker, 1 push/pull volume for coil split, 3 way toggle. The diagrams are only showing wires soldered to 4 of the 6 spots on the push/pull pot. But mine has wires soldered to all 6. The gray wire that I'm holding is the neck pickup wire. It appears to have a black grounded to the pot, a green and a red soldered to the far right lug of the push/pull, and a white soldered to the far left lug of the push/pull.

Sent from my ONEPLUS A6013 using Tapatalk


*

Offline ledvedder

  • Full Member
  • ***
  • 168
  • 3
    • View Profile
Re: Help with Washburn N24 wiring
« Reply #1 on: November 25, 2018, 11:31:56 AM »
Bueller?

Sent from my ONEPLUS A6013 using Tapatalk


*

Offline DarthPhineas

  • Hero Member
  • *****
  • 707
  • 20
    • View Profile
    • Darth Phineas Guitar Gear Reviews
Re: Help with Washburn N24 wiring
« Reply #2 on: November 25, 2018, 03:19:35 PM »
Guitarelectronics.com has a lot of diagrams. Be prepared to piece a few together to fit your needs.
Gear Reviews   |  Facebook   |   Twitter   |   Instagram

*

Offline ledvedder

  • Full Member
  • ***
  • 168
  • 3
    • View Profile
Re: Help with Washburn N24 wiring
« Reply #3 on: November 25, 2018, 03:42:57 PM »
Guitarelectronics.com has a lot of diagrams. Be prepared to piece a few together to fit your needs.
I didn't find any diagrams that match what I have in the N24.

Sent from my ONEPLUS A6013 using Tapatalk


*

Offline DarthPhineas

  • Hero Member
  • *****
  • 707
  • 20
    • View Profile
    • Darth Phineas Guitar Gear Reviews
Re: Help with Washburn N24 wiring
« Reply #4 on: November 25, 2018, 07:32:36 PM »
I didn't find any diagrams that match what I have in the N24.

Sent from my ONEPLUS A6013 using Tapatalk



Like I suggested:

Quote
Be prepared to piece a few together to fit your needs.

Take your time and you’ll figure it out. Or you can take it to a qualified tech.


Gear Reviews   |  Facebook   |   Twitter   |   Instagram

*

Offline darkbluemurder

  • Global Moderator
  • Hero Member
  • *****
  • 1590
  • 52
    • View Profile
Re: Help with Washburn N24 wiring
« Reply #5 on: November 26, 2018, 05:55:49 AM »
There are many ways to wire a coil tap. The diagrams you have seen probably show the normal way which would provide you with the inside coil as the active coil.

It looks like the wiring in your guitar is so that when split the outside coil of the neck pickup is active - which is by the way my preference as well. With the SD Jazz, the green wire would go to ground, black would go where the white wire is, and white and red would go where green and red are.

Good luck,
Stephan
Area 67, Area 58, Area 61, VV Pro 54, Injectors, VV HB2, Virtual Solo, SDS-1, Area T, Area Hot T, Area T 615, Virtual Hot T, Chopper T, Bluesbucker, Breed set, Air Norton, Super Distortion, DLX+ set, DLX-90, DP240, DP198, DP168, VPAF b, AT-1, Mo' Joe, FRED, Super 2; GS b